Tag Archives: commercial refrigeration maintenance

What Causes Commercial Refrigeration Leaks

There are many reasons why your commercial refrigeration system may be leaking. It could have been improperly installed, or handled poorly during service or maintenance. Some reasons why include:

  • Compressor discharge lines vibrations

Lines or fittings may break due vibrations, with most of a system’s vibrations being on or around the compressor discharge lines.

  • Corrosion

Exposure to certain liquids or condensation may cause corrosion. Copper exposed to anything acidic (including foods that are acidic) will corrode – an evaporator made of copper will develop pinhole leaks. Condensation forming can cause leakage to certain components such as a compressor rack. Cleaning the system with the wrong kind of cleaning material can cause corrosion. It’s very important that the correct cleaning material is used, as not every kind is compatible with every refrigeration system. Make sure technicians cleaning your system use the correct kind.

  • Fittings not tightened well

Threaded or flared fittings can cause leaks if they are under tightened or over-tightened to the point cracks form.

  • Improper Brazing

The brazing alloy used may be the incorrect kind, the metal before the brazing may not have been cleaned properly or the brazing technique was simply faulty, such as the temperature not being distributed well and the metal not melting as it should.

  • Metal contact with tubing

Copper tubing can come in contact with other tubing, or other harder metals such as steel and can rub through the tubing walls.

  • Missing valve caps/seals

Valve stems must have valve caps as well as seal/o-rings to prevent leaking.

  • Retrofitting or different kind of oil or refrigerant used

The parts of a system respond differently to different kinds of refrigerant or oils. If the system is being retrofitted with a new refrigerant or oil, some parts may swell differently than before and will need to be replaced.

  • Stress on tubing

Copper tubing that is not correctly supported will sag, like at 90 degree turns, and cause stress which can lead to lines or fittings to break.

  • Thermal stress

Expansion and contraction of the piping is normal, as the temperature in a refrigeration system is always changing. However, if there is not suitable room for it to expand the fittings supporting the pipe may break. Further more, constant expanding and contraction can affect the sealing of gaskets and seals.

An electronic leak detector may help with determining whether there is a leak or not. Make sure it can detect the same kind of refrigerant your system uses, as there are different types on the market, some that can detect some kinds of refrigerant better than others.

If you think your commercial refrigeration system has a leak, or would like to sign up for our preventative maintenance program please give us a call or contact us today. B & G Refrigeration is licensed by the State of Florida and all of our technicians are qualified to install  and work on your refrigeration system.

Have a great day!

Why Might a Compressor Fail

A few reasons why a compressor might fail:

  • Electrical problems – which is a major cause of compressor failure – including: faulty wiring done by the technician improperly wiring the compressor, low voltage, a bad or incorrectly-sized capacitor, compressor short-cycling or motor overload.
  • Liquid flooding is liquid returning to the compressor while it is still running. Liquid droplets dilute the oil, which prevents the parts of the compressor from being properly lubricated, which in turn leads to wear of parts and overheating. Slugging is the return of a mass of liquid, usually refrigerant and/oil. Compressors cannot compress liquids and will lead to a broken compentant usually if slugging occurs. To prevent liquid flooding/flooback and slugging, an accumulator can used. It will act as a reservoir, keeping liquid from entering the compressor.
  • Lack of oil, which as mention can be caused from liquid floodback, results in wear of the compressor, which will cause overheating and the compressor to seize up. Some reasons why the compressor isn’t properly oiled include: the gas velocity being too small to pick up the oil, a lack of refrigerant in the system, an oversized suction line, short-cycling or a blockage in the system.
  • Improper control settings can lead to the overheating of the system.
  • The only things allowed inside a refrigeration system is oil and refrigerant. Anything besides these is considered a contaminant, including air, scale, moisture or any kind of dirt. Contaminants can lead to system failure, so make sure that the system is clean and there is nothing besides oil and refrigerant in there, and even then, make sure those are at proper levels and not going into the wrong place.

Contact us today if you’re having troubles with your system’s compressor, and we’ll be sure to check it out for you.

Get a Free Estimate

B&G Refrigeration offers free estimates on new installations or replacements of: walk-in coolers and freezers, including box if needed, and refrigeration systems. We’ll send one of our people out to you, no trip charges or anything, for a completely free estimate.

If you’d like to set up a free estimate, contact us today!

And don’t forget, summer is practically here so make sure all your refrigeration is in working order!

Don’t Forget to have your Equipment Inspected

It’s getting close to summer! It’s important to have your equipment working when the heat hits, and it’s only going to get hotter from here. The last thing you want is for your refrigeration or ice machine to stop working in the middle of a hot, busy day.

We’d love for you to give us a call and to inspect your equipment. We also have a preventative maintenance program.

Contact us for any kind maintenance and let’s have a cool summer!

Reminder: Don’t forget preventative maintenance for your machines

It’s autumn, so now is a good time to have one of our technicians come over for preventive maintenance. It’s important for your systems to have regular maintenance in order to prevent breakdowns. Schedule one on our website or give us a call. We’ll come right over!

Thank you and have a nice autumn and winter!

Timely Adjustments to Avoid the Freeze-ups of Winter

Are your pressure controls for your walk-ins’ refrigeration systems set up properly to avoid freezing up during the winter months?

Pressure controls are installed on many refrigeration units to enable your outdoor unit to cycle off when the outdoor temperatures drop in order to keep the refrigeration unit from getting too cold and freezing up your evaporator.  If you’ve had this problem in the past or would like to avoid the possibility of this problem, contact our office and we can have the technician adjust your pressure controls for the coming colder weather.

It’s a good idea to have regular preventive maintenance.  Ask your technician when he visits and he can tell you what is covered.  We’re quite happy to arrange a maintenance program around your needs.  Just give us a call or set up service through our website.